8.20. Glasses of a wind window, window of a door of a back and sidewall

Removal and installation of a windshield

Note
You make installation of a windshield three together: two – outside, and one – in salon.

You carry out removal of a windshield in the following order:
1. In the top part of a window from the inside unbend an internal edge of a sealant a wooden shovel, at the same time slightly press on glass.
2. Take out glass together with a sealant, gradually giving it outside hand pressure and easy blows of the rubber hammer to the upper edge flew down from the inside.
3. Remove a sealant from glass.
You carry out installation of a new windshield in the following order:
1. Having missed the mark with mastic in a sealant grooves for glass and a flange of an aperture, put on a sealant glass.
2. Lay in a groove for an aperture flange a rope with a diameter of 3-4 mm so that its ends hanged down in the middle of glass from above.
3. Press outside glass together with a sealant to an otbortovka of an aperture and gradually extend a rope together with an internal frame of a sealant from the inside of glass. Along with a reverse side it is necessary to press on glass with a sealant. In the technological purposes it is the best of all to finish this operation in the middle of the lower part of a wind window.
4. Purify glass of mastic and other pollution.

Removal and installation of glass of a window of a door of a back

Note
You carry out installation of glass of a door of a back together. While one presses glass into an aperture outside, another by means of a mandrel puts on a sealant edge an aperture otbortovka.

You carry out removal of glass of a window of a door of a back in the following order:
1. Disconnect an electrical wiring of the warmed glass.
2. Hook a sealant edge from the inside of glass, along with it slightly press on glass in the top part.
3. Take out glass together with a sealant, gradually giving it outside hand pressure and easy blows of the rubber hammer to the upper edge flew down from the inside.
4. Remove a sealant from glass.
You carry out installation of new glass of a window of a door of a back in the following order:
1. Miss the mark with mastic in a sealant grooves for glass and a flange and put on a sealant glass so that the joint was located approximately in the middle of bottom edge of glass.
2. Press outside glass together with a sealant to an aperture otbortovka. As glass is not always freely included into a window aperture, use levers with rubber rollers by means of which carefully press glass to a nest. After that from the inside fill with a wooden shovel a sealant edge for an aperture otbortovka.
3. Purify glass of glue and mastic.
4. If necessary straighten a sealant from the outer side of glass by means of wooden shovels.
5. Connect an electrical wiring.

Removal and installation of glass of a sidewall
Removal and installation of glass of a sidewall are similar to removal and installation of a windshield. For installation of glass of a sidewall there are enough two people.

Removal and installation of a sealant of a doorway
You carry out removal of a sealant of a doorway in the following sequence:
1. Open a door.
2. Find the place of a joint of a sealant in the lower part of an aperture.
3. By means of flat-nose pliers remove the small site of a sealant that it was possible to push a hand and to remove the remained sealant from an aperture flange.
You carry out installation of a sealant of a doorway in the following sequence:
1. Insert into a tubular part of a sealant a connecting tube with the glue applied on its surface.
2. Put mastic in a groove of the reinforced part of a sealant of an aperture.
3. Put on the reinforced part of a sealant a doorway flange so that a tubular part of a sealant was outside (from a door), at the same time you watch that the joint of a sealant settled down in the middle of the lower line of a doorway.
4. For full landing of a sealant to an aperture flange slightly knock on it with the wooden hammer (on all contour of an aperture).

Removal and installation of sealants of an aperture of a window of forward and back doors
You carry out removal of sealants of an aperture of a window in the following order:
1. Lower glass in the lower situation.
2. A wooden shovel hook edges of sealants of an aperture of a window and take out a sealant from places of fastening.
You carry out installation of sealants of an aperture of a window in the following order:
1. Cut off new a sealant similarly old.
2. Establish the top sealant of glass.
3. Establish an external horizontal sealant and press on it before characteristic click.
4. Establish an internal sealant, press on it before characteristic click.