You carry out removal of a mirror in the following order:

Fig. 324. Body accessories: 1 – the rear-view mirror is left; 2 – facing of a forward door left; 3 – the rear-view mirror is internal; 4, 8, 10, 13, 18, 24 – screws; 5 – slip; 6 – facing of a forward door right; 7 – the rear-view mirror is right; 9 – cap; 11 – washers; 12 – facings of a plate of a hand-rail; 14 – gear washers; 15 – plates of fastening of a hand-rail; 16 – hand-rail are forward; 17 – hand-rail arms; 19 – hooks for clothes; 20 – hand-rail are back; 21 – the peak is antisolar right; 22 – holders of an antisolar peak; 23 – the peak is antisolar left; 25 – roof molding right; 26 – roof molding left

1. Take out two rubber caps of 9 (fig. 324) from internal facing 2 or 6 forward doors.

2. Unscrew two screws and remove facing 2.

3. Supporting by a hand a mirror through the lowered door glass, unscrew three screws 10 with washers 11 and remove a mirror.

You carry out installation of a mirror upside-down.

The intra saloon rear-view mirror is pasted on a windshield.

It is necessary for installation of a new intra saloon mirror:

1. To define visually an integrity of the protective film closing the gluing layer at a mirror support end face.

2. To degrease the place of gluing by the coarse calico moistened with the ethyl rectified alcohol in accordance with GOST 18300-87.

3. To sustain the fat-free surface within 2 min. for full evaporation of alcohol from the surface of glass.

4. To remove a protective film from the gluing layer.

5. To combine the pasted mirror surface with the place of gluing on a gleam.

6. To press a mirror support with effort of 8-10 kg and to hold it in the pressed condition of 10 pages.

Note Do not regulate a mirror within 30 min. after gluing.

You carry out removal of antisolar peaks in the following order:

1. Unscrew three screws 24 (see fig. 324) and remove a peak 21 or 23, previously having exempted a peak from gearing with the holder 22.

2. In need of removal of the holder unscrew the screw of fastening of the holder.

You carry out installation upside-down.

You carry out removal of a cover of the hatch of a bulk mouth in the following order:

1. Turn off two bolts of fastening of a cover at its open situation.

2. Uncover the hatch.

You carry out installation of a cover of the hatch of a bulk mouth upside-down, at the same time it is necessary to provide a uniform gap between a cover of the hatch and an aperture in the sidewall panel.

You carry out removal of the buffer of a cover of the hatch of a bulk mouth in the following order:

1. Open the hatch of a bulk mouth.

2. Delay a buffer short mustache towards a mouth and cut off the buffer on flange inside.

3. Remove the buffer rest from a flange.

You carry out installation of the new buffer of a cover of the hatch of a bulk mouth in the following order:

1. At open position of the hatch of a bulk mouth bring a buffer short mustache to a landing opening of a flange.

2. Pull with effort for a buffer short mustache from a mouth before click.

Note Before installation it is recommended to grease a buffer short mustache thickening with technical vaseline or any other available lubricant.

Removal of a hand-rail is carried out in the following order:

1. Remove facing 12 and a hook 19 (see fig. 324).

2. Unscrew screws 13 and 18 of fastening of a hand-rail and remove a hand-rail.

Removal and installation of a molding of a roof

You carry out removal of a molding of a roof in the following order:

1. Delay the forward end of a molding 25 or 26 (see fig. 324) and at the same time lift it up.

2. Pull out an internal short mustache of a molding from a groove in a roof on all length.

You carry out installation of a molding upside-down.